Cause:
This is a firmware issue, and will be fixed in a follow-on release.

Solution:
As a workaround, restore the system to factory defaults, and then select the new RAID mode.

A WD My Book drive connected to a HP Computer via FireWire does not format correctly after changing the RAID mode via the WD RAID Manager utility. This affects only the following drives: My Book Pro II, WD My Book Premium II, and WD My Book Studio I and II Edition.

Answer

Problem:
A My Book Pro II, Premium II, or Studio II Edition hard drive connected to a HP Computer via FireWire may not format correctly after changing the RAID mode via the WD RAID Manager utility. This issue only occurs on HP Computers running Windows XP that incorporate the Agere L-Fw3227-100 FireWire Chipset.

Cause:
This issue is caused by the BIOS of the HP Computer that has the Agere L-Fw3227-100 FireWire Chipset. HP is currently working on this issue and may release a BIOS update in the near future to resolve this issue.

Resolution:
There is currently no resolution to this issue when the hard drive is connected via the FireWire port on the HP Computer. To work around this issue, you can change the RAID mode and format the hard drive while connected to a USB port on the HP Computer. For more information about this issue, please contact HP Support.

Qty of 2 – 1TB internal hard drives:
• Spanning – 2TB
• RAID-0 – 2TB
• RAID-1 – 1TB
• RAID-5 – Not Supported

Qty of 3 – 1TB internal hard drives:
• Spanning – 3TB
• RAID-0 – 3TB
• RAID-1 – Not Supported
• RAID-5 – 2TB

Qty of 4 – 1TB internal hard drives:
• Spanning – 4TB
• RAID-0 – 4TB
• RAID-1 – Not Supported
• RAID-5 – 3TB

For more support information about the available RAID modes on the WD ShareSpace, please see the chart below:

Please Note:   Depending on how the WD ShareSpace RAID is setup, that RAID array may not be recoverable from a drive failure.

Qty of 2 – 1TB internal hard drives:

• RAID-0 – 2TB – (Not recoverable)
• RAID-1 – 1TB – (Recoverable)
• RAID-5 – (Not Supported)

Qty of 3 – 1TB internal hard drives:

• Spanning – 3TB – (Non recoverable)
• RAID-0 – 3TB – (Non recoverable)
• RAID-1 – (Not Supported)
• RAID-5 – 2TB – (Recoverable)

Qty of 4 – 1TB internal hard drives:

• Spanning – 4TB – (Non recoverable)
• RAID-0 – 4TB – (Non recoverable)
• RAID-1 (Double Mirror) – (Recoverable)
• RAID-5 – 3TB – (Recoverable)

For a recoverable RAID mode:
To recover the ShareSpace from Drive failure, or from a degraded RAID array, you must replace the failed drive with a Western Digital unformatted drive of the same model and size. Once the drive is replaced, the ShareSpace will re-sync the drive back into the RAID array and automatically start the RAID re-build. No further user intervention is needed, other than replacing the failed drive in the unit.

RAID is an acronym for Redundant Array of independent Disks. With RAID enabled on a storage system you can connect two or more drives in the system so that they act like one big fast drive or set them up so that one drive in the system is used to automatically and instantaneously duplicate (or mirror) your data for real-time backup.

There are three reasons you might want a RAID system of drives.

1. You need tons of storage space and you need it to be fast. (RAID 0)
2. You want to instantaneously and automatically backup your data. (RAID 1)
3. You want both. (RAID 5)

Which RAID mode should i use?

1. Speed (RAID 0)

Set in high-performance mode (also called striped mode or RAID 0) the storage system gives you the power you need when you’re:

• Designing huge graphics and need a lightning-fast photoshop scratch space.
• Recording large DV files while maintaining clean audio performance.
• Editing DV or HD video and want a smooth work flow with no dropped frames.
• Rendering complex 3D objects or special effects.
• performing disk-intensive database operations.
• Driven to be the first geek on your block with a computer so fast it blows your socks off.

Why is RAID 0 so fast? it’s a bit complicated, but suffice it to say that two or more heads, or in this case, drives, are better than one. picture multiple hoses filling a bucket at the same time or several men bailing a boat and you can understand why two drives striped are faster than one. Data is saved (striped) across both drives and accessed in parallel by all the drives so you get higher data transfer rates on large data accesses and higher input/output rates on small data accesses.

2. Data protection (RAID 1)

Set the system to data protection mode (also known as mirrored mode or RAID 1) and the capacity is divided in half. Half of the capacity is used to store your data and half is used for a duplicate copy.

Why do i want that kind of redundancy? it’s your data, your family pictures, your movie of baby’s first steps, your first novel. is it important? You decide. if it is, then RAID mirroring is for you.

3. Data protection and speed (RAID 5)

in systems with three or more drives (like 4 TB WD ShareSpace™ Network Storage System) we recommend that you set the system to RAID 5. This gives you the best of both worlds: fast performance by striping data across all drives; data protection by dedicating a quarter of each drive to fault tolerance leaving three quarters of the system capacity available for data storage.

About Spanning (Linear)

Spanning, which is not a RAID mode, combines all the drives in a system into one big volume so they act like one giant drive.  The drives are filled up one drive at a time.  The advantage of using this mode is that you can add more drives without having to reformat the system.